Dynex TV Video Accessories DX WD1335 User Manual
ASSEMBLY INSTRUCTIONS  
DX-WD1335  
Wood TV Stand  
Tools needed........................................... 2  
Parts ........................................................... 3  
Hardware.................................................. 4  
Assembly instructions ......................... 5  
 
DX-WD1335  
3
Parts  
Package contents: parts  
Note: Some parts have a label on the edge to help distinguish similar parts from each other. Use this illustration to help  
identify similar parts.  
Item  
Description  
Qty.  
Item  
Description  
Right front leg  
Qty.  
A
B
C
D
E
Right end  
Left end  
Top  
1
1
1
1
1
F
G
H
I
1
1
2
1
1
Left front leg  
Rear leg  
Lower shelf  
Back  
Skirt  
J
Stop molding  
Need help? Call 800-305-2204  
 
 
4
DX-WD1335  
Hardware  
Package contents: hardware  
Make sure that you have all the hardware necessary to assemble your new TV stand:  
Label  
Hardware  
Qty.  
Label  
Hardware  
Cam cover  
Qty.  
Q
6
K
2
Twist-lock® fastener  
Hidden cam  
R
S
1
1
L
13  
6
Glue  
M
N
Cam dowel  
Cam screw  
Warning  
label  
7
T
11  
4
Angle bracket  
O
P
2
2
Black 1-7/8" flat head screw  
Black 9/16"  
large head  
screw  
U
Wood dowel  
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
Need help? Call 800-305-2204  
 
 
DX-WD1335  
5
Assembly instructions  
Step 1:  
Caution: Assemble your TV stand on carpeted floor or on the empty carton to avoid scratching your stand or  
the floor.  
Push a Twist-lock® fastener (K) into each of the two the holes in the back (E).  
Important: Do not tighten the Twist-lock® fasteners in this  
step.  
You’ll need:  
K (2)  
Need help? Call 800-305-2204  
 
 
6
DX-WD1335  
Step 2:  
1 Push 13 hidden cams (L) into the ends (A and B), top (C), and back (E). Make sure that the arrows on the hidden  
cams (L) are pointing toward the closest edge.  
2 Insert the metal end of a cam dowel (M) into each hidden cam, except in the top (C) and short edge of each  
end (A and B).  
Important: Do not tighten the hidden cams in this step.  
Do not insert cam  
dowels into this part.  
Arrow  
Do not insert  
cam dowels  
into these  
edges.  
Arrow  
Arrow  
Arrow  
Insert the metal  
end of the cam  
dowel into the  
hidden cam.  
You’ll need:  
L (13)  
M (6)  
Need help? Call 800-305-2204  
 
DX-WD1335  
7
Step 3:  
Screw seven cam screws (N) into the front legs (F and G) and stop molding (J).  
You’ll need:  
N (7)  
Need help? Call 800-305-2204  
 
8
DX-WD1335  
Tightening hidden cams:  
In the remaining steps, use these illustrations for instructions on tightening hidden cams.  
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are  
not completely tightened will loosen, and parts may separate.  
Arrow  
Make sure that you turn the  
hidden cam a minimum of  
190° to a maximum of 210°.  
Note the position of the arrow  
on the hidden cam.  
Arrow  
210°  
In the illustration below,  
the hidden cam has not  
been tightened enough.  
190°  
You’ll need:  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
DX-WD1335  
9
Step 4:  
Align the stop molding (J) with the top (C), then tighten the three hidden cams.  
You’ll need:  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
10  
DX-WD1335  
Step 5:  
Align the ends (A and B) with the back (E), then tighten the two hidden cams.  
Edges with hidden cams  
Edge with Twist-lock® fasteners  
Edges with hidden cams  
You’ll need:  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
DX-WD1335  
Step 6:  
11  
Caution: Check the parts carefully before assembling. Disassembly of glued parts is extremely difficult.  
1 Fill the holes in the stop molding (J) 1/4 to 1/2 full with glue (R), then insert the wood dowels (P) into the holes.  
Wipe away the excess glue.  
2 Drop a few beads of glue (R) into the holes in the ends (A and B).  
3 Align the ends (A and B) and the back (E) with the top (C) and the stop molding (J). Make sure that the dowels,  
Twist-lock® fasteners, and cam dowels align with the correct holes, then tighten the four hidden cams and two  
Twist-lock® fasteners.  
Note: Wipe away the excess glue with a damp cloth.  
To use a Twist-lock®  
fastener:  
1 Insert the dowel end  
of the fastener into the  
hole of the adjoining  
part.  
Note: The dowel end of  
the fastener must  
remain fully inserted  
in the hole of the  
Fill the holes 1/4 to  
1/2 full with glue.  
adjoining part while  
locking the fastener.  
Dowel end  
2 Tighten the fastener  
with a Phillips  
screwdriver as tight as  
possible.  
®
Arrow  
Maximum: 210°  
Minimum:  
190°  
You’ll need:  
P (2)  
R (1)  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
12  
DX-WD1335  
Step 7:  
1 Attach two angle brackets (O) to the stop molding (J) using two black 9/16" large head screws (U).  
2 Fasten the skirt (I) to the stop molding (J) using two black 9/16" large head screws (U).  
Note: There are no pre-drilled holes in the skirt. The screws tighten into the groove.  
You’ll need:  
O (2)  
U (4)  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
DX-WD1335  
Step 8:  
13  
1 Align right front leg (F) with the right end (A) and the left front leg (G) with the left end (B), then tighten the four  
hidden cams (L).  
2 Attach the rear legs (H) to the ends (A and B) using four black 1-7/8" flat head screws (T).  
Important: Make sure that the rear legs (H) angle out and away from the stand.  
You’ll need:  
T (4)  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
14  
DX-WD1335  
Step 9:  
Fasten the lower shelf (D) to the ends (A and B) and back (E) using seven black 1-7/8" flat head screws (T).  
Long finished edge  
You’ll need:  
T (7)  
Phillips screwdriver  
Need help? Call 800-305-2204  
 
DX-WD1335  
Step 10:  
15  
1 Carefully turn your TV stand upright.  
2 Apply the warning label (S) to the top (C) so that the TV will hide the label. Peel off the backing and apply the  
label as shown in the diagram.  
Note: This is a permanent label intended to last for the life of the product. After you apply the label, do not try to  
remove it.  
3 Push a cam cover (Q) onto each visible hidden cam.  
You’ll need:  
Q (6)  
S (1)  
For customer service, call: 800-305-2204 (U.S./Canada markets)  
Need help? Call 800-305-2204  
 
Certificate of Conformity  
1. This certificate applies to the Sauder Woodworking Product  
identified by this instruction booklet.  
2. This certificate applies to the compliance of this product with  
the CPSC Ban on Lead-Containing Paint (16 CFR 1303).  
3. This product was manufactured by:  
Sauder Woodworking Company  
502 Middle Street  
Archbold, Ohio 43502  
(419) 446-2711  
4. Date of Manufacture: _______________  
Lot number: 345399  
www.dynexproducts.com (800) 305-2204  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.  
© 2012 BBY Solutions, Inc.  
All rights reserved.  
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and  
brand names are trademarks of their respective owners.  
12-0625  
ENGLISH  
 

EAW Speaker SB1002 User Manual
Extron electronic Stereo Amplifier MDA 3V 1x3 User Manual
Extron electronic Stereo Receiver RGB 201 Rxi User Manual
Fender Musical Instrument 112 User Manual
Fisher Price Motorized Toy Car W9418 User Manual
Frigidaire Dishwasher 675000612098 User Manual
Frigidaire Freezer FFHT2126L User Manual
Garmin GPS Receiver 010 00782 2C User Manual
Gateway Computer Keyboard NV53A User Manual
GE Cordless Telephone 28311 User Manual